The Grate Guys Tools
com.thegrateguys/tools · v1.0.0 · MCP 2025-11-25
Planning calculators for metal grating, drainage covers and fabrication.
Reachability
reachable
checked 2026-11-21 05:34 UTC
Registry status active
Tools pinned 15
78b9ee7ff4e9
Tools last changed
unchanged since first capture 2026-11-17
Provenance
Registry namespace com.thegrateguys
(domain verified by the official registry)
Remote endpoints
https://thegrateguys.com/mcp (streamable-http)
Observed changes
| When (UTC) | Event | Detail |
|---|---|---|
| 2026-11-17 05:30 | first capture | 15 tools pinned |
Pinned tool definitions (15)
| Tool | Description |
|---|---|
| bar_grating_load_calculator | Finds the lightest welded steel bearing bar (19-W-4 or 15-W-4, smooth or serrated) that carries a clear span and load within a deflection limit. |
| bar_grating_load_tables | Looks up the safe uniform load (U), safe concentrated load (C), deflections and weight for welded steel bar grating by bearing bar size and span. |
| aluminum_stainless_bar_grating_load_calculator | Safe load, deflection and the lightest bearing bar for aluminum 6063-T6 and stainless 304, 316, 304L and 316L bar grating at 1-3/16 in bar centres. |
| accessible_grating_opening_checker | Checks the clear opening between bearing bars against the Ontario Building Code 13 mm limit for barrier-free paths of travel, and the widest bar spacing that would pass. |
| galvanizing_coating_thickness_calculator | Minimum average hot-dip galvanized coating grade by steel category and thickness, in mils, microns and ounces of zinc per square foot, with total zinc for a surface area. |
| guard_and_railing_code_checker_ontario | Whether a guard is required, its minimum height, opening limit, climbing rule and design loads under the Ontario Building Code Part 9 and Part 3 for a described situation. |
| steel_stair_calculator_ontario | Allowed riser counts, riser height, tread run, flights, width, headroom and handrail height for a total rise under Ontario Building Code Part 9. |
| steel_weight_calculator | Theoretical weight of carbon steel plate, flat bar, round bar, square bar, angle, square or rectangular tube and round pipe, in pounds and kilograms. |
| trench_drain_grate_load_class | The EN 1433 load class, A 15 to F 900, and its test load in kN for where a trench drain goes and what drives or rolls over it. |
| bollard_spacing_and_footing_calculator | Counts the bollards for a frontage and clear gap, checks the gap against vehicle and wheelchair guidance, gives typical footing and concrete for a standard (not crash rated) steel pipe bollard, and explains crash ratings. |
| steel_beam_lintel_span_check | The steel angle lintel or steel beam that the 2024 Ontario Building Code Part 9 tables list for an opening width in a brick or stone veneer wall or a masonry wall, with the 150 mm bearing rule. Not a stamped design. |
| catch_basin_grate_and_frame_size_finder | Names the Ontario Provincial Standard Drawing for a catch basin inlet type, checks the grate bearing on the frame ledge against the NAAMM minimum, gives the range of bearing bar lengths that sit on the ledge, and lists the EN 1433 load... |
| fence_and_gate_post_spacing_and_weight | Post count and spacing for a chain link or ornamental steel fence run, chain link footing depth and gate post size, and the weight and hinge loads of an ornamental steel gate leaf. |
| trench_drain_flow_capacity_calculator | The flow a trench drain has to handle from a paved area (rational method with Toronto City rainfall rates from Environment and Climate Change Canada) and the flow the channel carries (Manning), with the narrowest channel that works. |
| loading_dock_height_and_leveler_check | The grade a dock leveler works at between the lowest and highest truck bed you serve, against the 10% (electric) and 15% (gas or diesel) limits, the shortest standard leveler length that fits, and whether two makers published working... |
Get alerted when this changes.
Email the moment com.thegrateguys/tools drifts, dies, or revives.
Status badge
[](https://toolpin.dev/servers/com.thegrateguys/tools)
Maintain this server? Add the badge to your README. It links your users to this live status page.